纸张水份测试仪 KT-50
筛选
  • 地区
    全部
  • 会员级别
    全部
筛选
  • 截止时间
    全部
仪表展览网>产品库>纸张水份测试仪
价格: 面议
产品型号:KT-50
品牌:73625
公司名称:眉山新建华通信技术有限公司
地:四川眉山
发布时间:2024-10-23
眉山新建华通信技术有限公司
产品简介
●意大利克洛特纳仪表公司生产的KLORTNER纸张水分仪,能通过简单的接触,快速测量出50~500g/m2之间的各种纸张、纸箱、瓦楞纸等的含水率,且不损坏被检测的材料。 ●先进的电磁波传感技术能穿透纸张深度达50mm,产生一个三维立体磁场进行现场测量。因此,它是准确度极高的纸张测湿仪表。 ●仪表开机后40秒自动关机,有效节约电能,保护仪器更长时间的使用。 ●仪器设有低电压显示,当
产品详情

一、技术指标

        1、测量范围:250%

        2、显示:LCD液晶显示

        3、档位调整:50500g/m21-5档)

        4、扫描深度:050mm

        5、精度:±0.5%

        6、体积、重量:120×60×26(mm),150g

二、使用方法

       选择档位开关:

          1档:纸箱、瓦楞纸板

          2档:50以下纸张、浆板纸等

          3档:瓦楞纸、书写纸、牛皮纸、箱板纸

          4档:新闻纸、白板纸、涂布纸

          5档:铜版纸、复印纸、传真纸

         由于纸张结构不同,其介电系数亦不同;以上档位为建议档位,如有误差,请进行对比校验。如:测量某一已知水分为8%的纸张,调整档位开关为4档时,所测数字显示为08.0,则以后再测量同类纸张时应将档位选为4档。

三、注意事项

 1、由于KT-50型纸张水分仪电磁波穿透深度达50mm,所以测量纸张的平均水分时,要求被测纸张或纸箱叠加厚度不得小于50mm

2、如仪表开机后显示不在00.0±00.5范围以内,请将电池后盖打开取出电池,在电池盒内侧有一零位调节器。正值不到零位,逆时针调节;反之,顺时针调节。

3、由于本纸张水分仪采用电磁波感应方式进行测量,测量时仪器周围或底部不得有金属物或其它感应物,否则会对测量精度有所影响。

 

 

PAPER  MOISTURE  TESTER  KT-50

Introduction 

  The electronic meter allows the measurement of the moisture in the paper in the size 120×60×26mm and the weight of 150g.It is a battery-operated pin instrument,fully transistorized and operates on a pure dielectric constant measurement with HF(High Frequency) waves.The method of measurement is based on a balance system,which measures the DK-value(dielectric-value) of the moist material,after precious deduction of the DK-value of the dry material and thus the pure moisture content is indicated.

FEATURES

  KT-50 paper moisture meter produced by Italy KLORTNER company permits to measure the moisture content of many kinds of paper products ranging from 50 to 500g/m²,quickly by simply contacting and eliminate paper damage.

  The precise dielectric constant measurement with HF waves can get the moisture content of the depth of 50mm at most.

  After being used for 40 seconds,KT-50 moisture meter will automatically turn off to retrench the power supply for protecting itself.

  KT-50 paper moisture meter will remind you of low voltage as well.

TECHNICAL DATA

Measuring Range:0%~50%

Resolution:0.1%

Repetition Accuracy: ±0.5%

Display:3½LCD

Scanning Depth:50mm(1.96 inch) at most

Density Range:50 to 500g/m²

Work Environment: -5 to 50

Power Supply:9V(6F22) shut off after used 40 seconds automatically

Dimension:120×60×26mm

Weight:150g

APPLICATION

Before measuring,get a right selector according to the paper species table or paper density.

With the sensor of KT-50 touching nothing,pressONbutton.Turn carefullyZERObutton in the battery cover,till the readings on the screen is between 00.0±00.5.

With the sensor of the meter,touch the wood to be measured fully.As soon as the meter is in touch with the paper surface,the moisture content is indicated.

NOTICE

The paper to be measured should be bigger than the sensor of the meter.

Nothing else can be placed under the paper to be measured,otherwise the measurement will be inaccuracy.

If the thickness of the material to be measured is lower than 50 mm,to avoid wrong readings,it is sufficient to hold the items without its bottom touching anyting.

商铺其他产品
联系商家 立即询价
发布询价单