阿美特克Ametek加压泵T-620/T-620H|阿美特克T-620H的产品介绍

描述

阿美特克T-620H液压泵用手动可以产生最高到344BAR的压力；阿美特克T-620用手动可以产生最高到206BAR的压力, 阿美特克T-620和T-620H可以用于快速准确地检测压力表，变送器，传感器和其他压力测量仪器。

建议使用的流体介质是：油基介质，矿物油或者使用不会对铝、铜、不锈钢、聚四氟乙烯，聚碳酸酯和浸湿的橡胶产生腐蚀的液压介质。不要使用溶剂或合成液体，否则会使液压泵受到损害。

操作指南

1．拿掉储液容器顶端的填充塞，填充流体介质到充满储液容器的2/3处。盖上并拧紧填充塞。

2．将要校准的仪器连接在测试软管的末端；标准压力表与压力测试接口连接。并将测试软管绷紧。

注意：不要绷得太紧、不要将测试泵与高压力源连接，以避免对测试泵和操作人员造成伤害。

3．面向测试接口，逆时针旋转左边的压力释放阀直至完全打开。

4．捏动手柄直到流体介质明显地处于测试软管中。

5．拉紧测试软管和被测设备。

注意：软管可能在初始状态下被预充满了流体介质来帮助加速液压泵的操作。

6．继续捏动手柄直到容器中的气泡停止运动，然后用手顺时针将压力释放阀拧紧。

7．捏动手柄直到大概获得测量上想要的压力。然后旋转右侧的压力微调阀直到获得准确的测试压力。

8．在完成校准测试后，逆时针旋转压力释放阀释放压力至0 BAR并移开被测量的设备。

9．拧紧软管末端的塞子以防止流体漏出并存放于安全的地方。

系统 C - 液压手泵阿美特克T-620H

This easy-to-use hand pump is specially designed for high pressure applications. The pump has a built-in reservoir, vent valve, and vernier valve for fine adjustment. The pump has a dual pressure output - one for the test object and one for the IPI indicator.

Pressure range, T-620 0 to 200 bar / 3,000 psi

Pressure range, T-620H 0 to 350 bar / 5,000 psi

Ready-to-use pressure systems

Ready-to-use pressure systems for the DPC-500, APC, CPC, and IPI calibrators. For all pressure systems the pump and the indicator are separate systems. Therefore a replacement of the pump does not mean that you have to send the complete system for repair. Maintenance of the instrument is also made easy. Recalibration of the unit can be performed locally with an accurate pressure reference: No need to send the unit back to the manufacturer for recalibration. If you do require a factory calibration, the pump and indicator are independent and only the indicator needs to be returned. JOFRA pressure calibrators are as standard delivered as individual indicators or as a complete calibration systems ready to use in a carrying case, including pump, hose, set of fittings, batteries, test leads, user manual, and a NIST traceable calibration certificate.

此页是美国阿美特克T-620干体炉的详细技术参数说明，详情请咨询邦亚电子。

系统 C - 液压手泵 阿美特克T-620H

系统 C - 液压手泵阿美特克T-620H