KINAX 2W2 智能型转角变送器

KINAX 2W2

        很多年来，在复杂的环境下都需要来测转角（诸如：工控阀门开度控制、金属转子流量计输出、震动、敲击、农林等）。我们采用的固态电容系统远远优于其它系统。现在，我们在全世界最先制造出能够通过系列通讯接口和Windows软件的进行组态和线性化的转角变送器KINAX 2W2。
       其不同的地方为：
      OEM型可以安装在你所使用的任何场所
      可用于位置反馈
      Eex ia型
      KINAX 2W2角位变送器，利用无接触，电容传感系统测得轴的角位。测量输出为与测量值成正比的4-20mA，且为独立于负载的直流信号。

* 特有的无接触电容传感系统

* 测量范围，转动方向，特性，开关点和另外的附加功能均可以通过PC机编程/由于2W2的适用性强，使用户可以：简化设计，缩短供货期，减少库存量

* 转角的测量范围：0...10 到 0...50 或 0...50 到 0...350°

* 测量输出（输出/电路）两线制连接（4.. 20 mA信号）

* 测量扭矩非常小(< 0.001 Ncm, 直径2 mm的轴) 。优势：轴可以自由转动，毫不影响与其相连的被测设备，即对被测轴没有反作用力。

* 小尺寸，仅48mm直径。优势：可以任意安装（OEM）

* 可选本安防爆型，符合EEx ia IIC T6，用在易爆场所

* 可仿真测量并输出/便于安装调试阶段，对相关其它设备（系统）进行仿真测试

* 测量值通过软件可以显示在电脑屏幕上，并可以获得趋势图

* 灵活调整：独立调整模拟输出，零点和量程

* 输出量特性：可编程设定为线性，V型曲线或任意的特性曲线

* 驱动轴可以360度任意旋转

* 带串行接口

Transmitter with a contact free, capacitive sensor system for the acquisition of the angular position of a shaft. The output is a load-independent DC current signal of 4...20 mA proportional to the measured value.

Patented contact free capacitive sensor system

Measuring range, direction of rotation, characteristic, switching point and other additional functions programmed using PC / Simplifies project planning and engineering, short delivery times, low stocks

Measuring range of angle of rotation: 0...10 to 0...50 or 0...50 to 0...350°

Measuring output (output/powering circuit) in two-wire connection (4...20 mA signal)

Very low torque (< 0.001 Ncm, with 2 mm shaft)
Advantage: The shaft can be rotated practically without any reaction effects and is therefore not a «load» on the connected devices.

Compact size, only 48 mm Æ
Advantage: it can be installed anywhere (OEM)

Type of protection “Intrinsically safe” EEx ia IIC T6 / Can be mounted within the hazardous area

Simulation of measured values / The testing of the subsequent device chain is already possible during the installation phase

Measured value acquisition / Display of the instantaneous value and a trend graph of the measured value on the screen

Adjustment / Independent fine adjustment of the analog output, zero position and measuring range

Characteristic of the output value / Programmable as a linear, V-characteristic, or any characteristic curve

The shaft can be turned through a full 360°

Serial interface

Article No.	mechan. Angle Range	Meas. Range	Reversing point	Direction of Rotation	Output Charact.
760-1111100	50°	0.. 50°	55°	Clockwise	Linear
760-1211100	350°	0..350°	355°	Clockwise	Linear

Order other variants with complete order code (760-.... .... ....) in accordance with the data sheet.